Grounding finger for the rear facing camera iphone 4s

Contents

  1. iPhone 4S Front Camera Replacement
  2. Add your answer
  3. 14 Best iPhone 4S Logic Board Replacement images | Iphone 4, Iphone 4s, Licence plates

Lift the cable cover from its edge nearest the top and remove it from the iPhone. Be careful not to break any components off the surrounding area on the logic board as you pry upwards. Remove the rear camera from the iPhone. There is a small rubber gasket that sits underneath the rear-facing camera. Make sure that it is properly seated before reassembly.

This may require a significant amount of force.

iPhone 4S Front Camera Replacement

Remove the SIM card and its holder. To disconnect the cables, use the edge of a plastic opening tool to gently lift their connectors up and out of the sockets on the logic board.

Be careful not to break any of the small and delicate surface mount components as you disconnect the cables. Carefully grasp the grounding clip and remove it from the iPhone. Before reassembly, be sure to clean all metal-to-metal contact points on the grounding clip not the mating halves of connectors with a de-greaser such as windex or isopropyl alcohol.

Add your answer

The oils on your fingers have the potential to cause grounding issues. Remove the 2. This bumper can fall off of the logic board when removed or get stuck to the cables and fall off later. Use a small flathead screwdriver to remove the single 3. Remove the logic board. Before reassembly, be sure to clean all metal-to-metal contact points on the logic board not the mating halves of connectors with a de-greaser such as windex or isopropyl alcohol.

There is a small rubber bumper that sits on the top edge of the logic board where the digitizer and screen cables come through the case. It protects the cables as they bend over the top of the logic board. This can either get stuck to the cables or fall off the logic board when it comes out. Look back over step 22 for more details.


  • Bella Jocalia Handmade Fashion;
  • Follow by Email.
  • .
  • .

This finger rests on top of the PCB, screwed down, and covered with the adhesive black plastic tape. Pry the vibrator up to release it from the adhesive securing it to the iPhone.

Remove the vibrator. Edit Step 29 Remove the speaker enclosure assembly from the iPhone.

14 Best iPhone 4S Logic Board Replacement images | Iphone 4, Iphone 4s, Licence plates

Before reinstalling the speaker enclosure assembly's screws, be sure the Wi-Fi grounding fingers are installed below the lip in the iPhone's metal case as seen in the second picture. Before reassembly, be sure to clean all metal-to-metal contact points between the grounding fingers of the Wi-Fi antenna and the case of the iPhone with a de-greaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to cause wireless interference issues. Edit Step 30 — Display Assembly Remove the small pieces of black tape covering the display mounting tabs.

These corner screws are not the same thickness as the other 1. Set them aside separately.

Edit Step 31 Remove the 1. Removing the headphone jack makes it easier to access this screw, particularly during reassembly. The oils on your fingers have the potential to cause grounding issues. Be careful: DO NOT clean the connectors' mating halves. Make sure not to lose the small grounding finger for the back camera near the power button. The grounding finger is placed on top of the PCB, screwed down, and covered with the adhesive black tape. Using the edge of a plastic opening tool, carefully lever the metal front facing camera retainer from the case of your iPhone.

Send this link via e-mail. Step 1 - Rear Panel. Step 3. Step 4 - Battery Back to top. Step 9. Step Step 12 - Back Camera Back to top. Leave a comment. Send this link via e-mail Send via e-mail. Thanks http: View the answer I have this problem too Subscribed to new answers.

Is this a good question? Yes No. Voted Undo. Score 0. The All-New. The high performance electronics repair kit. Most Helpful Newest Oldest.